PRESS RELEASES
NEW WIRELESS BURST DETECTION SYSTEM - READ MORE...
ELFAB INTRODUCES PORTABLE BURSTING DISC INSTALLATION AID, TEST-TEL
ELFAB LAUNCH DETECTION SYSTEM FOR OEM MARKET
ELFAB ENSURE NEW PANEL RANGE MEETS CUSTOMER REQUIREMENTS
NEW NON-INVASIVE BURST DETECTION MONITORS PROCESS TEMPERATURE
More...
 
CAREERS AT ELFAB
None at present
HR Policy
Submit a CV
 
Worldwide Contacts
 
Products > Forward >  Flat Composite (FC)
 
Printer Friendly Version Download PDF Version View Schematic Installation Guide
 
 

The Flat Slotted Lined tension-loaded composite bursting disc offers and economic solution to many very low pressure applications.

This non fragmenting design is offered in an extensive size and material range, bringing, enhanced protection, reliability and leak-tightness through its unique tri-membrane construction.
   
  • Can be used with Elfab’s unique ATEX approved Integral Flo-Tel™ burst detection
  • Very low pressure capability
  • Corrosion resistant
  • Non torque-sensitive
  • Non-fragmenting design
Specifications
SIZE RANGE
25mm to 800mm (1" to 32")
BURST PRESSURE RANGE
0.07 bar g to 3.5 bar g (1 psig to 50 psig)
TEMPERATURE RANGE
-80 to 250C (-112 to 480F)
MAXIMUM OPERATING RATIO
40% of minimum burst pressure (36% of nominal burst pressure)
FRAGMENTATION ON BURST
non-fragmenting design
RELIEF VALVE ISOLATION
suitable
VACUUM SERVICE
back pressure support required
FLUID COMPATIBILITY
liquid, gas or vapour
KR VALUES
not available
TORQUE-SENSITIVE
no
CYCLE LIFE
poor
MATERIAL RANGE
Stainless Steel as standard, others available.
REVERSAL RATIO
<1 (fail safe),depending on back pressure support
DAMAGE RATIO
<1 (fail-safe)
LEAK TIGHTNESS
good
PERFORMANCE TOLERANCE
+/- 10% (zero manufacturing design range)
PROTECTIVE LININGS
not available

Pressure and Solutions Intelligence
Depending on back pressure requirements, back pressure supports may be required. On Flat Slotted Lined bursting disc devices the back pressure support is integral in the holder.

To find out how our products could benefit you and your organisation, or for Specifications outside those stated on this data sheet please contact Elfab directly or via your local representative.

Specifications and Performance

BURST PRESSURE RANGE in barg (psig) at 20 °C (68 °F)
Nominal Bore
Nickel Top sectionFluoropolymer Seal
Stainless Steel Top SectionFluoropolymer Seal
(mm)
(inch)
Min
Max
Min
Max
25
1
1.4 (20.3)
2.5 (36.3)
2.5 (36.3)
3.5 (50.8)
40
1 ½
1.0 (14.5)
1.9 (27.6)
1.8 (26.1)
3.3 (47.9)
50
2
0.5 (7.25)
1.2 (17.4)
0.9 (13.1)
2.1 (30.5)
65
2 ½
0.4 (5.8)
0.9 (13.1)
0.7 (10.2)
1.6 (23.2)
80
3
0.35 (5.1)
0.8 (11.6)
0.6 (8.7)
1.4 (20.3)
100
4
0.2 (2.9)
0.7 (10.2)
0.4 (5.8)
1.3 (18.9)
150
6
0.15 (2.2)
0.7 (10.2)
0.25 (3.6)
1.3 (18.9)
200
8
0.1 (1.45)
0.6 (8.7)
0.2 (2.9)
1.1 (16.0)
250
10
0.1 (1.45)
0.5 (7.25)
0.15 (2.2)
0.8 (11.6)
300
12
0.07 (1.02)
0.4 (5.8)
0.1 (1.45)
0.7 (10.2)
350
14
0.07 (1.02)
0.6 (8.7)
400
16
0.07 (1.02)
0.5 (7.25)
450
18
0.07 (1.02)
0.5 (7.25)
500
20
0.07 (1.02)
0.5 (7.25)
600
24
0.07 (1.02)
0.5 (7.25)
700
28
0.07 (1.02)
0.5 (7.25)
800
32
0.07 (1.02)
0.5 (7.25)

PERFORMANCE TOLERANCE (ZERO MANUFACTURING DESIGN RANGE)
Burst Pressure at 20C (68F)
0 to 50C (32 to 122F)
Above 50C (122F) Below 0C (32F)
Above 0.5 (7.25)
+/- 10%
+/- 15%
0.3 (4.35) to 0.5 (7.25)
+/- 15%
+/- 20%
0.2 (2.9) to 0.3 (4.35)
+/- 20%
+/- 25%
0.2 (2.9) and below
+/- 25%
+/- 30%

STANDARD TEMPERATURE RANGE °C (°F)
Seal Membrane Material
Minimum
Maximum
Fluoropolymer
-80 (-112)
250 (482)

FREE FLOW AREA / MINIMUM NET FLOW AREA (MNFA)
Nominal Bore
Value
mm
inch
mm2
in2
25
1
261
0.40
40
1 ½
805
1.25
50
2
1388
2.15
65
2 ½
2468
3.83
80
3
4078
6.32
100
4
6422
9.95
150
6
14152
21.94
200
8
26025
40.34
250
10
49094
76.10
300
12
70695
109.6
350
14
96224
149.2
400
16
125680
194.8
450
18
159064
246.5
500
20
196375
304.4
600
24
282780
438.3
700
28
384895
596.6
800
32
502720
779.2
Note: Up to 200mm Support is integral to disc. Above 200mm support will be a separate item, possibly integral to holder.

HOLDER DIMENSIONS
Nominal Bore (B)
Height (C)
Outside Diameter (A)
mm
inch
mm
inch
BS EN 1092
ANSI
25
1
38.4
1.51
PN 6 to 50
150 to 600 lb
40
1 ½
38.4
1.51
PN 6 to 50
150 to 600 lb
50
2
38.4
1.51
PN 6 to 50
150 to 600 lb
65
2 ½
40
1.57
PN 6 to 50
150 to 600 lb
80
3
42
1.65
PN 6 to 50
150 to 600 lb
100
4
47
1.85
PN 6 to 50
150 to 600 lb
150
6
62
2.44
PN 6 to 50
150 to 600 lb
200
8
58
2.28
PN 6 to 50
150 to 600 lb
250
10
58
2.28
PN 6 to 50
150 to 600 lb
300
12
58
2.28
PN 6 to 50
150 to 600 lb
350
14
66.5
2.62
PN 6 to 50
150 to 600 lb
400
16
66.5
2.62
PN 6 to 50
150 to 600 lb
450
18
71.5
2.81
PN 6 to 50
150 to 600 lb
500
20
71.5
2.81
PN 6 to 50
150 to 600 lb
600
24
88
3.46
PN 6 to 50
150 to 600 lb
700
28
102
4.02
PN 6 to 50
150 to 600 lb
800
32
116
4.57
PN 6 to 50
150 to 600 lb


The holder is configured to accept Elfab’s ATEX-approved Integral Flo-Tel™ burst detection switch as standard.

To ensure the correct performance of a bursting disc, it must be used in its correct holder, as specified by the bursting disc manufacturer.


Pressure Intelligence

 The data shown on these sheets represents the standard offering from Elfab. Depending upon the requirements of your application, Elfab maybe able to provide a solution based on this product but outside the standard operating parameters. In addition, Elfab produces an extensive range of alternative products which maybe more suitable for your requirements.

As a result of extensive testing, Elfab can advise on these choices, or on other technical matters, such as discharge requirements, temperature testing, material selection and corrosion resistance, customised designs and burst detection.

To discuss your specific product or service requirements please contact your Elfab representative.

© 2004 Elfab Ltd.

 
Click here to email our sales department. Click for more contact details.